skip to main
|
skip to sidebar
http://www.facebook.com/profile.php?id=1738290019
My Facebook profile
WELCOME TO MY BLOG
Here you'll find some info on Ducati repair and modifications along with photos. I've got stuff for sale too, so check out the older posts. Please leave comments about anything you see, good or bad.
Thanks for looking,
Steve
Search This Blog
Sunday, April 15, 2007
Nice clean piston ready for rings...
No comments:
Post a Comment
Newer Post
Older Post
Home
Subscribe to:
Post Comments (Atom)
BLOG LIST
A Little Bit of Everything
WOOD-N-STEEL
8 years ago
THE CAFE PROJECT
THE BIKE IS SOLD!!!!
9 years ago
My Blog List
Lauren Methia's Photo Blog
Blog Archive
►
2016
(7)
►
January
(7)
►
2014
(2)
►
January
(2)
►
2013
(13)
►
December
(1)
►
October
(1)
►
August
(3)
►
June
(3)
►
March
(2)
►
February
(2)
►
January
(1)
►
2012
(27)
►
August
(2)
►
July
(1)
►
June
(1)
►
May
(10)
►
April
(4)
►
February
(3)
►
January
(6)
►
2011
(36)
►
December
(2)
►
November
(3)
►
October
(5)
►
July
(2)
►
June
(1)
►
May
(5)
►
April
(11)
►
March
(2)
►
February
(4)
►
January
(1)
►
2010
(50)
►
December
(3)
►
November
(3)
►
October
(1)
►
September
(5)
►
August
(1)
►
July
(3)
►
April
(2)
►
March
(5)
►
February
(8)
►
January
(19)
►
2009
(44)
►
December
(1)
►
November
(10)
►
October
(2)
►
September
(1)
►
August
(2)
►
July
(1)
►
April
(2)
►
March
(12)
►
January
(13)
►
2008
(43)
►
November
(6)
►
July
(1)
►
June
(15)
►
March
(10)
►
February
(10)
►
January
(1)
▼
2007
(73)
►
December
(2)
►
November
(8)
►
October
(12)
►
August
(5)
▼
April
(46)
HOLDING THE PULLEY
OFF SET KEY IMAGE
OFF SET WOODRUFF KEY
Here the bent pointer sits nicely on the helpe...
Here it is snapped onto the shim. ...
The following is a follow up to my original Power ...
Dial indicator with flexible holder and homemade...
Homemade pointer sitting on shim. Horizontal Int...
Aluminum plate with flexible support checking H....
Both closing shims installed. Here a rubb...
A shim can be made smaller by up to 3 thousa...
Make sure the shim is cool, then check the thickne...
Shim ready to be installed.Sometimes a burr will...
I've included this image to show how I've labelled...
Write everything down.I measure in "inches" beca...
My feeler gauge setup makes life easier.
The top of the shim should be flush with the t...
It’s critical that the keepers are seated correc...
Installing the half rings, or keepers. A little ...
It’s a plastic spacer made from a garden hose ...
Here’s my homemade rocker shaft removal tool i...
Keep all the valve train pieces organized. M...
RANDOM NOTES Here’s my universal opening shim...
RANDOM NOTES Here’s my universal opening shim...
Valves are “lapped” back in.
All valves are removed and cleaned along with ...
I set up my table with wood head support and fee...
I find it easier to check valves with heads re...
•Top rocker is stock, bottom is a reconditione...
•Top rocker is stock, bottom is a reconditione...
•On the right is a rocker arm reconditioned by...
My 1998 748 didn’t have an oil feed hole in th...
Here a 4mm set screw is inserted into the oil ...
Nice clean piston ready for rings...
Work in a clean, organized environment
Fit each ring in bore and check the end gap
CLEANING PISTONSFITTING NEW RINGS
S •Wax can also be used in the combustion chamb...
Note lines in chamber where head gasket sits...
Measurements can be taken with a micrometer or v...
CHECKING SQUISH---DUCATI 748 1MM Solder is positi...
CHECKING "SQUISH"Special wax in varying thic...
CHECKING "SQUISH"1MM Solder is positioned in...
2325=64:=827=XROQDF>23238:;;27275ot1lsi"> The spor...
I custom paint helmets and bodywork.You can see e...
my chron plus dash
About Me
Unknown
View my complete profile
No comments:
Post a Comment